Washing machine not draining water: filter, pump and module

Water stays in the tub and the machine won't go into the spin — we check the filter, the pump and the module output that drives it.

If water remains in the tub after the wash, the machine won't go into the spin, the door won't open and a drain code appears on the display. Most of the causes are simple, and you can check them yourself: a clogged filter, a kinked hose, the sewer connection. If these are fine, it is the turn of the pump and the electronics that control it.

Check these yourself first

  1. Unplug the machine.
  2. Put a container and a towel under the filter. The filter is usually at the bottom of the front panel, behind a small flap. Some models have a thin hose next to the filter for draining the water.
  3. Drain the water slowly. Before opening the filter fully, turn it slightly so that the water flows out slowly; there may be several litres of water in the tub. The water may be hot — if the program included heating, wait.
  4. Clean the filter. Coins, buttons, hair and bits of fabric are the most common blockages. Look into the filter housing: the pump impeller should turn easily by hand.
  5. Check the drain hose. The hose should not be kinked or raised too high, and the sewer connection should not be clogged.

Close the filter, plug the machine in and run the “drain” or “spin” program.

The filter is clean, but the water won't drain

What you hearLikely cause
The pump hums, but the water doesn't goThe impeller is jammed or broken — mechanics
The pump makes no sound at allThe pump coil is broken or no voltage reaches it — the triac (relay) in the module, the wiring
The water drains, but the machine still shows a codeThe water level sensor (pressure switch) or the module input that reads its signal

We check the pump, its wiring and the control output in the module. If no voltage reaches the pump, the cause is in the module — we restore the triac and its circuit. Replacing the pump itself is mechanical work and outside our scope; if the pump is faulty, we tell you. A pump that has been clogged for a long time can also overheat and burn out the control element in the module, so it is worth checking the output after the pump has been replaced.

Codes

Samsung — 5C (5E), LG — OE, Indesit and Hotpoint-Ariston — F05 and F11, Bosch and Siemens — E18 (F18), Electrolux and Zanussi — E20 and E21, Haier — Err2, Candy and Vestel — E03, Midea — E21 — washing machine error codes.

If the machine has stopped completely with water inside and the door won't open — machine stopped during the wash. If the machine won't spin because the water isn't draining — washing machine not spinning. Repair of the pump control starts from 80 AZN.

Opening the drain filter of a washing machine

Get a repair quote

Choose your device and leave your number — we will contact you as soon as possible.

Thank you! Your request is received — we will contact you as soon as possible.

Useful articles

  • Understanding and Fixing Incorrect Water Circulation Issues
    Washing Machine Problems

    Understanding and Fixing Incorrect Water Circulation Issues

    Incorrect water circulation in washing machines can lead to a myriad of issues, from unclean clothes to potential damage to the machine itself. Understanding the causes and solutions to this problem is essential for maintaining your appliance's efficiency and longevity. In this article, we explore t...

  • How to Fix Water Leaking Inside Machine Cabinet
    Washing Machine Problems

    How to Fix Water Leaking Inside Machine Cabinet

    When you discover water leaking inside your machine cabinet, it can be a concerning and potentially costly issue. Understanding the possible causes and knowing how to address them can save you both time and money. In this article, we will explore the common reasons behind this problem and provide pr...

  • Troubleshooting Check Valve Not Locking Issues
    Washing Machine Problems

    Troubleshooting Check Valve Not Locking Issues

    When your washing machine's check valve fails to lock, it can lead to frustrating water and pump-related issues. Understanding the root causes of this problem and knowing how to address them can help restore your appliance to efficient operation. In this article, we delve into the common reasons beh...

  • Understanding and Fixing Water Level Sensor Reading Error
    Washing Machine Problems

    Understanding and Fixing Water Level Sensor Reading Error

    Water level sensor reading errors can disrupt the efficient functioning of your washing machine, leaving you frustrated with incomplete or faulty cycles. Understanding the common causes and solutions for these errors is essential for maintaining your appliance's performance. In this guide, we'll del...

  • Drain Pump Loud Noise: Causes and Solutions
    Washing Machine Problems

    Drain Pump Loud Noise: Causes and Solutions

    The unexpected clamor from your washing machine can be both alarming and perplexing. Among the common culprits is a loud drain pump. Understanding why your appliance sounds like it's preparing for takeoff can save you time, money, and perhaps your sanity. This article delves into the causes and solu...

  • How to Fix a Clogged Inlet Filter in Your Washing Machine
    Washing Machine Problems

    How to Fix a Clogged Inlet Filter in Your Washing Machine

    The inlet filter in your washing machine plays a crucial role in ensuring the clear flow of water into the drum. However, when it becomes clogged, it can lead to several issues, including poor washing performance and water supply interruptions. In this guide, we explore the causes, symptoms, and sol...

Prices

Washing machine not draining water: filter, pump and modulefrom 80 AZN

These are starting prices: we tell you the exact amount after diagnostics.

FAQ

Frequently asked questions

My washing machine won't drain. What should I do first?

Unplug the machine, put a container under the filter, drain the water slowly, clean the filter and check the hose. The cause is often a blockage in the filter.

The filter is clean and the pump makes no sound. What is the cause?

No voltage is reaching the pump (the triac or relay in the module, the wiring), or the pump coil is broken. We check them and restore the module output.

Do you replace pumps?

No, replacing the pump is mechanical work and outside our scope. We repair the electronics that control the pump.

How much does a pump control repair cost?

Repair of the pump control — the triac or relay in the module — starts from 80 AZN. We tell you the exact price after finding the faulty part.

Why does my washing machine not fill with water but still turn the drum?

The machine runs through the programme steps, but there is no water in the drum: the tap is closed, the hose is kinked, the inlet screen is clogged or the pressure is low. If the water supply is fine, the inlet valve is not opening — its coil is broken or the command from the module is not reaching it. The opposite also happens: the water level sensor (pressure switch) “thinks” the water is already in. We check the valve coil and the module output that drives it during diagnostics.

Contacts

Send a request — we will quote the price

Google Maps loads only when you press the button

Get a price

Leave your number — we will contact you as soon as possible.

Thank you! Your request is received — we will contact you as soon as possible.