Audio Equipment Repair: Amplifiers, Speakers, Subwoofers, Cinema Sound
Innova Service has been repairing electronics in Baku since 2008. We repair the electronics of audio equipment: amplifiers and AV receivers, active speakers and subwoofers, soundbars, Bluetooth speakers, and the sound systems of cinemas and conference halls. We work with Yamaha, Denon, Marantz, Onkyo, Pioneer, Sony, Bose, Harman Kardon, JBL, Samsung, LG and other brands.
Our audio repair technician, who specializes in speakers and amplifiers, works on the electronics: home theater systems and receivers, music centers, hi-fi and hi-end amplifiers, and wireless speaker boards.
- The speaker hums or crackles. A poor contact, dried-out capacitors in the power supply, a faulty amplifier — we find out why the speaker hums by taking measurements.
- The speaker does not charge or does not work with a PC. The charging port and circuit, the battery, the USB and Bluetooth module.
- Distorted amplifier sound, mute mode, going into protection. The audio path, the output transistors (thermal breakdown, burnt-out transistors), a short circuit at the amplifier output.
Repairs start from 30 AZN. We find the cause first, then quote the exact price; work starts only with your approval, and we give a warranty on the work done.
Faults we repair
| What happens | Likely cause |
|---|---|
| It does not turn on at all | The power supply, the fuse, the protection relay |
| It turns on, but there is no sound, “Protect” mode | The output transistors or the amplifier IC, the protection circuit |
| One channel does not work | That channel's amplifier, a relay, the output |
| Crackling, hum, background noise | Capacitors, grounding, the input circuit |
| The subwoofer produces no sound or “knocks” | The subwoofer amplifier board, the power supply |
| HDMI ARC, the optical input or Bluetooth does not work | The input board, a module, the firmware |
| The volume knob “crackles” | The potentiometer, the encoder |
Cinema and hall sound
We also repair the powerful amplifiers, processors and active speakers of cinemas and of conference and event halls. In such systems, downtime means a direct loss, so the faulty unit is checked and repaired at our service center, and the cause and price are given in advance.
How we repair
- Diagnostics. The power supply, the amplifier stages, the protection circuit and the inputs are checked; measurements are taken with a dummy load.
- Price. Quoted in advance, once the faulty part has been found.
- Repair. Output transistors, ICs, capacitors and relays are replaced.
- Testing. The equipment runs for a long time at different volume levels; we give a warranty on the work.
If the speaker driver itself (cone, voice coil) is damaged, we tell you during diagnostics. We do not sell spare parts separately — a faulty part is only replaced as part of a repair. Car audio — car multimedia repair.
Why amplifiers go into protection and burn out
- Load impedance too low. 4-ohm speakers on an output rated for 8 ohms, or several speakers in parallel — the output stage overheats.
- Shorted speaker wires. A thin strand touching the chassis or the neighbouring wire burns out the output transistors.
- Overheating. An amplifier in a closed cabinet without ventilation runs at its limit.
- Mains voltage surges. The power supply and the protection circuit suffer.
What you can check yourself
If the amplifier switches on and immediately goes into protection (Protect), disconnect all the speakers and switch it on again. If the protection does not trigger, check the wires and the speakers. If it triggers even without a load, the fault is inside — do not keep switching it on: that can add to the damage.
TV sound: soundbars and AV receivers
A soundbar or AV receiver is usually connected to the TV via HDMI ARC / eARC or an optical cable. When the sound suddenly disappears, the cause may lie in the audio equipment — the HDMI input board, the audio processor, the power supply — or in the TV itself: its HDMI port or its firmware. At diagnostics we test the audio device with a separate signal source; if the fault is in the TV, we tell you — TV repair.
When a repair pays off
Good amplifiers, receivers and studio monitors last for decades, and their electronics can be restored: capacitors, output transistors, relays and potentiometers are replaced. Repairing such equipment almost always costs less than buying new. With an inexpensive Bluetooth speaker whose main board has burnt out, however, the repair may cost close to a new one — we tell you so plainly at diagnostics.
Amplifier faults we repair
- Amplifier stuck in protect mode, or one channel dead. Output transistors, the protection circuit, a DC offset at the output — often an amplifier burnt by a speaker short.
- Loud pop from the speakers at switch-on, humming output. The speaker protection relay and its delay circuit; humming usually comes from dried filter capacitors in the power supply.
- Amplifier overheating and shutting down. Thermal protection, bias setting, the fan and dust inside the case.
- Class D and Class AB amplifiers. Home amplifiers, home theater and home cinema amplifiers and receivers, PA systems (a zone with no sound), and car amplifiers — home and car amplifier repair at component level.
- Water or fire damage. We clean and restore the board; if a chip is discontinued or the board is too badly burnt, we tell you after diagnostics when an amplifier cannot be repaired.
Home audio repair, including portable speakers: a speaker not charging usually has a faulty charging port, battery or charging circuit. Send a photo or video of the fault on WhatsApp for a preliminary estimate; the exact price is quoted after diagnostics.
We also repair tube (valve) amplifiers: the tubes, the high-voltage power supply, filter capacitors and bias circuits — with the bias set after the repair.
Tube amplifiers and hi-fi
When repairing a tube amplifier, we check the tubes, the high-voltage power supply, the filter capacitors, and the output and bias circuits, and after the repair we set the tubes' idle current. We also work with hi-fi equipment from Naim, Marantz, Denon, Yamaha, Onkyo, Cambridge Audio and other brands; the repair of a Naim amplifier, or any other, starts with diagnostics, and we quote the price in advance.
Professional and premium sound systems: Crown, QSC, Meridian
Cinemas, concert venues and conference halls run professional power amplifiers from Crown, QSC and other brands. Most of them have a switch-mode power supply and a Class D output stage, while older models have a heavy transformer and a Class AB output. We repair the power supplies, output modules, protection circuits and DSP control boards of these amplifiers at component level. In clubs and halls, amplifiers work in dusty conditions and at full power: the fans and heatsinks clog with dust, the output stage overheats and goes into protection, so during the repair we also clean the cooling system and check the fans. In premium sound systems such as Meridian — active DSP speakers and amplifiers — we repair the electronics of the amplifier and processor boards; if a speaker driver itself is damaged, we tell you after diagnostics whether a suitable one is available. In premium equipment, a faulty part is replaced with a component of the same specifications so that the character of the sound does not change.
Linear amplifiers: the transformer and the filter capacitors
In a linear amplifier, the power supply consists of a transformer, a rectifier bridge and large filter capacitors. Over the years, electrolytic capacitors dry out: their capacitance drops, hum appears, the bass “sags” at volume, and the amplifier may go into protection. During restoration we replace the filter capacitors, check the bridge and the soft-start circuit, and measure the transformer windings, the insulation and the built-in thermal fuse. If a transformer winding has burnt out, we tell you after diagnostics whether it can be replaced with a suitable transformer.
- Signs of dry filter capacitors. Hum that is audible even with no signal, a bulging or leaking capacitor, distortion on bass notes.
- A transformer fault. The fuse blows at switch-on, the transformer buzzes loudly or overheats.
- A soft-start circuit fault. At switch-on the lights dim for a moment, the breaker trips or the relay does not click in — in an amplifier with a large transformer, the resistor or relay that limits the inrush current is faulty.
- Harmonic distortion. As the volume goes up, the sound becomes “dirty” and harsh: most often the bias current of the output transistors has drifted, the transistors have aged or the capacitors have dried out. We test the amplifier with a signal generator and an oscilloscope on a dummy load, and after the repair we set the bias and check the shape of the sine wave at different power levels.
Waterproof Bluetooth speakers: the housing and the seal
The housing of the JBL Charge, Flip, Xtreme and other waterproof speakers is closed with a rubber seal and adhesive. If water has got into the speaker, switch it off first and do not charge it: moisture causes corrosion in the charging port and on the board. During the repair we clean the board, replace the corroded components and then reassemble the housing on its seal. However, we do not promise the factory water resistance of a speaker that has been opened — after the repair we advise against putting it in water.
In-car audio is a separate direction: head units and amplifiers — car stereo fixing and repair.
Besides audio equipment, we repair the electronics of TVs, computers and household appliances — electronics repair in Baku.

Get a repair quote
Choose your device and leave your number — we will contact you as soon as possible.
Prices
| Audio Equipment Repair: Amplifiers, Speakers, Subwoofers, Cinema Sound | from 30 AZN |
|---|
These are starting prices: we tell you the exact amount after diagnostics.
Frequently asked questions
My amplifier goes into “Protect” mode. Can it be repaired?
Yes, most often the output transistors or the protection circuit are faulty; they are replaced.
Do you repair Bose and Harman Kardon speakers?
Yes, we repair the electronics of active and Bluetooth speakers.
How much does audio equipment repair cost?
Repairs start from 30 AZN; we quote the exact price after diagnostics.
My speaker distorts at high volume — is it the driver or the amplifier?
It can be either. We measure the amplifier with a dummy load: if the signal is clean, the cause is the driver (voice coil, cone); if not, it is the amplifier's output stage or power supply.
Do you repair old amplifiers and receivers?
Yes, we repair the electronics of old transistor amplifiers and receivers: dried-out capacitors, output transistors, relays and crackling potentiometers are replaced.
My soundbar does not detect the TV via HDMI ARC. What should I do?
First check the ARC and CEC settings on the TV, the cable and the HDMI port. If they are fine, the fault may be in the soundbar's HDMI board or in the TV's port — diagnostics show which one.
Do you repair Bluetooth speakers?
Yes: the charging port and circuit, the battery, the board and the amplifier. If the cause is the speaker driver itself, we tell you after diagnostics.
Can you give an exact amplifier repair price over the phone?
No: the same symptom — no sound, for example — can come from a blown fuse or from the output stage. Send a photo or video of the fault on WhatsApp for a preliminary estimate; the exact price is quoted after diagnostics.
Do you replace speaker drivers?
If a suitable driver is available, yes — we tell you after diagnostics. The speaker's amplifier, board and power supply are what we repair.
Send a request — we will quote the price
- 070 262 19 19Call us
-
5a Ahmad Rajabli St. (Life Centre)Baku, AZ1052
-
Mon — Fri, 10:00–18:00Sat, Sun — closed
- service@innova.azEmail