Electronic Circuit Board Repair in Baku: Component Level
Innova Service has been repairing electronic boards in Baku since 2008. Component-level repair is the core of our work: instead of replacing the whole board, we find the faulty component on it — a capacitor, transistor, IC, relay or fuse — replace it, and restore broken solder joints and traces. This is often much cheaper than buying a new board, and for older equipment it is the only option.
Board repair starts from 80 AZN. We find the cause first, then quote the exact price and repair time; work starts only with your approval, and we give a warranty on the work done.
Which appliances' boards we repair
| Appliance | Boards and modules |
|---|---|
| TV | Main board, power supply, T-Con, LED driver, HDMI ports |
| Monitor | Power supply, control board, backlight driver, electronics of medical monitors |
| MacBook and laptop | Main board, power circuits, recovery after liquid damage |
| PlayStation | HDMI port, power supply, main board |
| Washing machine | Control module, inverter motor driver, display panel |
| Refrigerator | Control board, inverter compressor board, sensors |
| Air conditioner | Indoor and outdoor unit boards, inverter board |
| Dishwasher | Control module, heating and pump control |
| Coffee machine, microwave oven | Control board, power supply, sensors |
| UPS and inverters | Power board, charging circuit, control board |
| Computer | Motherboard, power supply, graphics card, BIOS chip |
| Car multimedia systems | Board of the head unit and multimedia system, amplifier, screen and touch control |
| POS equipment | Board and power supply of POS terminals, electronic scales, kiosks |
| Audio equipment | Amplifier output stage, power supply, protection circuit |
| Solar power systems and industrial inverters | MPPT controller, BMS board, power modules, drivers |
What component-level repair is
A board is made up of dozens or hundreds of components, and when it fails, usually only one or two of them have broken down. The technician traces the circuit with measurements — checking supply voltages, signals and the condition of the components — and finds the faulty part. Then they desolder and replace it, restore the damaged traces and test the board under load. Replacing the whole board, by contrast, is expensive and, for older models, often impossible.
Typical board faults
- Power section. Voltage surges burn out the fuse, the varistor, capacitors and power ICs — the device does not turn on at all.
- Swollen capacitors. Over the years they dry out and lose capacitance — the device behaves strangely and restarts by itself.
- Power transistors and modules. The power components that drive motors, compressors and backlights burn out from overload.
- Relays and triacs. Their contacts burn or “stick” — the device stops performing a certain function.
- Corrosion. Liquid spills, condensation and moisture destroy traces and contacts.
- Cracked solder joints. Vibration and temperature changes crack the solder — the fault comes and goes.
- Memory and firmware. The configuration or the firmware gets corrupted — the device does not start or shows an error.
How the repair works
- Diagnostics. Visual inspection, measuring supply voltages and signals.
- Price and time. Quoted in advance, once the faulty part has been found.
- Repair. Faulty components are replaced, solder joints and traces are restored, and the firmware is rewritten if necessary.
- Testing. The board is tested under load.
- Warranty. We give a warranty on the work done.
When a repair is not possible
If the board has burnt to charcoal, the inner layers of a multilayer board are damaged, or a programmed chip has failed and its firmware cannot be found, restoration may be impossible. We tell you this plainly during diagnostics, and the decision is yours.
How to protect a board
- If the voltage often surges, use a voltage stabiliser or a surge-protected extension lead.
- If liquid gets into a device, unplug it immediately and do not switch it on until it has dried out.
- Do not block the ventilation holes: overheating ages capacitors and power components quickly.
How to tell that a board is faulty
- The device shows no sign of life. No indicator, no sound — most often the power section has failed: the fuse, the power IC or the capacitors.
- The device turns on and immediately shuts off. The protection trips: one of the power transistors has shorted, or the voltage in some circuit is out of range.
- An error code on the display. Washing machines, air conditioners, refrigerators, UPS units and inverters use error codes to point to the faulty circuit — the code makes diagnostics faster.
- A burning smell, a darkened spot on the board. A component has overheated and burnt out; unplug the device at once and do not switch it on again.
- The fault comes and goes. A cracked solder joint or an oxidised contact — the device fails when it warms up or vibrates.
- The buttons, touch panel or display do not respond. The control board, its power supply or its connecting cable is faulty.
How diagnostics are done
First, the board is inspected under magnification for burnt, swollen or darkened components, cracked solder joints and traces of corrosion. Next, the supply rails are measured for short circuits, and the board is carefully powered from a current-limited supply so that a faulty component cannot cause further damage. A shorted component is located by the heat it gives off, and the supply voltages and control signals are checked one by one along the circuit. This way both the fault itself and its cause are found.
Components replaced most often
- Electrolytic capacitors — dry out and swell in the heat, causing ripple in the power supply.
- MOSFET and IGBT transistors — the power switches of motors, compressors and inverters; they burn out from overload.
- Power ICs (PWM controllers) — the “heart” of switch-mode power supplies; they often fail after a surge.
- Relays and triacs — switch heaters, pumps and valves; their contacts burn.
- Fuse and varistor — the first to take the hit of a surge; before replacing them, we check why they blew.
- Optocouplers and regulator ICs — hold the voltage steady in the power supply; when they fail, the voltage “drifts”.
- Memory chips — store the settings and firmware; if corrupted, the firmware is rewritten.
Repair or a new board: what to consider
| Criterion | Board repair | New board |
|---|---|---|
| Price | Usually much cheaper: only the faulty components are replaced | Expensive, sometimes close to the price of the device itself |
| Availability | Possible even for an old model | Often no longer sold for older models |
| Compatibility | The board's firmware and settings are kept | Sometimes the firmware must be written or the settings redone |
| Cause | The cause of the fault is found and eliminated | If the cause (for example, a shorted motor) remains, the new board burns out too |
What a quality board repair depends on
A quality repair does not end with replacing the faulty component. The technician first finds out why it burnt out: if a short in the motor, a mains surge, moisture or overheating was the cause, a new component will fail too unless that is dealt with. New components are matched by their ratings — voltage, current, capacitance, temperature range — and the soldering temperature is kept under control so that neighbouring components and the traces of a multilayer board are not damaged. After the repair, the board is tested inside the device itself, under a real load.
Electronics of business equipment
For shops, restaurants and offices, board repair matters even more: when POS equipment, a UPS, a server or an industrial inverter stops, the business stops too. We repair the boards of POS terminals, electronic scales, payment kiosks, UPS units and inverters the same way: the faulty component is found and replaced, and the equipment is tested in working mode. We quote the price and repair time in advance so that you can plan your work.
Before you hand a board in for repair
- Unplug the device and do not keep switching it on until the cause is clear — every attempt can add to the damage.
- Do not wash the board yourself or heat it with a hair dryer: after a liquid spill, we remove the corrosion with special cleaning fluids.
- Note the error code and what happened before the failure — a power cut, a spill, a fall.
- If you removed the board from a large appliance yourself, photograph the connectors and cables so that it is easy to reconnect later.
Warranty and testing
We give a warranty on the work done; its length depends on the type of appliance, and we tell you before the repair. After the repair, the board is tested in working mode: supply voltages, control signals, heating of the power components. We do not sell spare parts separately — components are replaced only as part of a repair.
PCB repair at component level: a printed circuit board (PCB) from a washing machine, a TV, an air conditioner or another appliance is traced by our PCB repair technician with schematics and measurements, and only the failed component is replaced — a relay, triac, regulator, capacitor or a burnt track.
Besides circuit boards, we repair TVs, computers, household appliances and other devices — all services: electronics repair.
Read more: electric stove and oven repair.

Get a repair quote
Choose your device and leave your number — we will contact you as soon as possible.
Prices
| Electronic Circuit Board Repair in Baku: Component Level | from 80 AZN |
|---|
These are starting prices: we tell you the exact amount after diagnostics.
Frequently asked questions
Is it better to repair a board or replace it?
In most cases a repair is more cost-effective: one or two components on the board fail, and they are replaced. For older models, where new boards are no longer sold, a repair is the only option.
Which appliances' boards do you repair?
Boards from TVs, monitors, laptops, MacBooks, PlayStations, washing machines, refrigerators, air conditioners, dishwashers, coffee machines, microwave ovens, UPS units, inverters and other electronic equipment.
Can a board damaged by liquid be restored?
Often, yes: the corrosion is cleaned off, and the damaged components and traces are restored. The sooner you contact us, the better the chances.
How much does board repair cost?
Repairs start from 80 AZN. The exact price depends on the faulty part, and we quote it after diagnostics.
Do you give a warranty on the repair?
Yes, we give a warranty on the work done.
Do you sell spare parts or boards?
No, we do not sell spare parts or boards separately. Faulty components are replaced only as part of a repair, and they are covered by the warranty together with the work done.
How long does a board repair take?
It depends on the fault and on the components needed; we do the repair as quickly as possible. We give the exact time after diagnostics, together with the price.
Do you also repair the boards of POS and audio equipment?
Yes: we repair the boards of POS terminals, electronic scales, kiosks, amplifiers, active speakers and car stereos at component level.
Do you repair computer motherboards?
Yes, we repair the motherboards of desktop computers and laptops: power circuits, swollen capacitors, the BIOS chip, ports and corrosion after liquid damage.
Can you restore a board's firmware?
Yes, if the firmware in the memory chip is corrupted, we write it again. If the firmware is available only from the manufacturer and cannot be found, restoration may be impossible — we tell you this during diagnostics.
Can I hand in just the board from a large appliance?
Yes. For washing machines, refrigerators, air conditioners and dishwashers we repair only the electronics, so handing in the control board or module is enough. Smaller equipment — laptops, TVs, UPS units, coffee machines — is accepted whole.
Can a board burnt by a voltage surge be repaired?
In most cases, yes: a surge usually burns out the fuse, the varistor, the power IC and capacitors, and those are replaced. If the board has not charred, the chances of restoring it are high.
Which brands' boards do you repair?
There are no brand restrictions: we repair boards from Samsung, LG, Bosch, Siemens, Beko, Electrolux, Indesit, Sony, Philips, APC and other manufacturers, because the work is done at the level of the circuit and individual components.
What happens if the fault comes back after the repair?
If the same fault recurs within the warranty period, we check the board again and fix it under the warranty. Keep the document we give you after the repair for this.
Is board diagnostics paid?
Yes, diagnostics are paid: the technician finds the faulty part by taking measurements. After that we quote the repair price and start work only with your approval.
My induction hob will not turn on — what should I do?
Check the circuit breaker and the socket, switch the hob off at the mains for a few minutes and turn it on again. If that does not help or the hob trips the breaker, do not switch it on again: the fault is usually in the power supply, the power module or the touch panel — that is a board repair.
Send a request — we will quote the price
- 070 262 19 19Call us
-
5a Ahmad Rajabli St. (Life Centre)Baku, AZ1052
-
Mon — Fri, 10:00–18:00Sat, Sun — closed
- service@innova.azEmail