Laptop screen (panel) replacement
Cracked screen, lines, spots: the panel is matched by model code and connector.
The screen (panel) is the part of a laptop that gets damaged most often: a drop, an object left between the lid and the keyboard, pressure in a bag. A cracked panel cannot be repaired — it is replaced. But not every black screen or line is a panel fault: the cause may be the cable, the backlight or the motherboard. That is why we test first and replace second. Repairs start from 100 AZN.
When the screen needs replacing
| What you see | What is done |
|---|---|
| A crack, a black spot, a “spider web” | Panel replacement |
| Permanent colored lines, part of the screen shows nothing | Usually the panel; the cable is checked first |
| The picture disappears when the lid moves, lines come and go | The display cable — repaired without replacing the panel |
| Black screen, a faint picture is visible with a torch | The backlight or its circuit on the board |
| Black screen, no picture on an external monitor either | Motherboard, graphics chip — motherboard repair |
How the panel is matched
Laptop screens of the same size are not always interchangeable. The panel is matched by:
- Model code — printed on the label on the back of the panel (for example, NV156FHM-N48, B140HAN04.0).
- Connector — 30 or 40 pins, and its position (left, right, bottom).
- Size and mounting — 14, 15.6, 16, 17.3 inches; panels with side mounting brackets or slim panels without them.
- Refresh rate and type — 60, 120, 144, 165 Hz; TN, IPS, OLED; touch screens.
In a gaming laptop, a high-refresh screen can be replaced with a standard 60 Hz panel, but the difference will be noticeable in games — we tell you this in advance.
How we replace it
- Check. An external monitor, the cable and the backlight are tested — we make sure the fault is in the panel.
- Matching. The panel is chosen by model code, connector and refresh rate.
- Replacement. The screen bezel is carefully removed, the panel is replaced, the cable is checked.
- Testing. Brightness, colors, dead pixels, the webcam and the lid at every angle; we give a warranty on the work.
If the screen is cracked
- Do not press on a cracked screen: cracks spread and liquid crystal may leak.
- If you need your files, you can keep working by connecting the laptop to a monitor via HDMI.
- Open and close the lid carefully: a damaged bezel can also break the cable.
All services — laptop repair. MacBook screens — MacBook screen replacement.
Types of laptop panels: TN, IPS, OLED
The panel is the screen itself: a layer of liquid crystals or organic LEDs, a control board along the bottom edge and, in LCD panels, a backlight inside. Laptop panels come in several technologies. When replacing, we fit a panel of the same type, or a better one if the model allows it.
| Panel type | How to recognize it | What matters when replacing |
|---|---|---|
| TN | Colors and brightness shift when you look at the screen from the side, from below or from above; common in budget and older laptops with a 1366×768 resolution | The most affordable type; if the connector and mounting match, an IPS panel can often be fitted instead |
| IPS and similar (AHVA, ADS, PLS) | Wide viewing angles, colors do not shift when the screen is tilted; used in most modern laptops with Full HD and higher | We match brightness and color gamut: a panel with about 45% NTSC looks noticeably paler than one with 100% sRGB |
| OLED | Deep blacks and no backlight — every pixel emits its own light; found in ASUS ZenBook and VivoBook OLED, Lenovo Yoga, Dell XPS, HP Spectre, Samsung Galaxy Book | Replaced only with an OLED panel with the same or a compatible code: LCD panels have a different connector, cable and thickness |
| Matte or glossy finish | A matte finish cuts glare; a glossy one gives richer colors but reflects lamps and windows | If the model came in both versions, you can choose; we tell you about any difference before the replacement |
Resolutions differ too: HD (1366×768), Full HD (1920×1080), 1920×1200 on 16:10 screens, as well as 2.5K, 2.8K and 4K. A panel with a different resolution fits only if the connector and interface match, so we check the resolution by the code, not by eye.
Panel connectors: eDP and LVDS, 30 and 40 pins
The panel connects to the motherboard through a cable, and the panel connector must match the cable in interface, pin count and position. The same number of pins does not mean compatibility: 30-pin eDP and 30-pin LVDS are different interfaces, and a panel of one kind will not work on a cable of the other.
- eDP, 30 pins — most laptops from around 2013 onwards with HD and Full HD 60 Hz panels.
- eDP, 40 pins — 120–360 Hz panels, 2.5K and 4K resolutions, some touch and OLED screens: four lanes carry more data.
- LVDS, 40 pins — laptops up to around 2013 with an LED backlight; fewer new panels of this kind are made, so we look for compatible ones.
- LVDS, 20 and 30 pins — old laptops and netbooks; the oldest have a lamp backlight (CCFL) powered by a separate inverter board.
- Connector position — on the right or the left when you look at the back of the panel, sometimes in the middle: the cable simply will not reach a connector on the other side.
- Touch panels — touch signals go either through a separate connector or through the same 40-pin connector as the picture.
How we match a panel by its code
The laptop model name is not enough: the factory fits panels from different manufacturers into the same model, and one product line comes in HD, Full HD, 144 Hz or touch versions. That is why the key is the code of the panel itself. It is printed on the label on the back of the panel.
- We read the code. The first letters show the manufacturer: NV and NT — BOE, B — AU Optronics, N — Innolux, LP — LG Display, LTN and ATNA — Samsung, LQ — Sharp. The next digits usually give the diagonal: 140 — 14 inches, 156 — 15.6, 173 — 17.3. The rest is the resolution, type and version. For example, NV156FHM-N48 is a 15.6-inch Full HD panel by BOE, and B140HAN04.0 is a 14-inch Full HD panel by AU Optronics.
- We check it against the laptop maker's part number. Lenovo uses an FRU number, HP a spare part number, Dell a DP/N, and other brands have their own numbers. This number shows which panels suit the model.
- We check the specifications: the connector and its position, resolution, refresh rate, brightness, color gamut, finish, thickness and mounting — brackets at the top and bottom, on the sides, or no brackets with adhesive strips.
- We agree it with you. If there is an exact replacement, we fit it; if there is only a compatible panel with differences — for example, from another manufacturer or with a matte finish instead of glossy — we tell you in advance.
If the label is damaged or missing, we identify the panel by the laptop model, by data on which screens were fitted to that model, and by the connector and mounting. A replacement can also be an upgrade: if the connector, interface and mounting match, an IPS panel can often replace a TN one, Full HD can replace HD, and a bright 100% sRGB panel can replace a dull 45% NTSC one. We check this by the code before ordering: not every laptop model supports another resolution or refresh rate.
Touch screens and 2-in-1 convertibles
A touch laptop has a touch layer in front of the image: either a separate glass bonded to the panel or a layer inside the panel itself. In 2-in-1 convertibles — Lenovo Yoga, HP Envy x360 and Spectre x360, Dell Inspiron 2-in-1, ASUS VivoBook Flip, Acer Spin — the screen is usually replaced as a complete assembly: the panel, the touch layer and the cover glass are bonded at the factory.
- Only the glass is cracked, the picture is intact. The assembly is still usually replaced: the glass and the panel are bonded, and they cannot be separated without risking the panel.
- The screen registers touches on its own, the cursor jumps. The touch layer, its cable or its controller is damaged; we test each of them separately — sometimes replacing the cable is enough.
- There is a picture, but touch does not work. We check the touch cable, its connector and its power on the board first, then the controller, and only then the touch layer itself.
- After the replacement we test touch across the whole screen, multi-touch and the pen, if the laptop supports one.
High refresh rate screens in gaming laptops
Gaming laptops — ASUS ROG and TUF Gaming, Lenovo Legion and LOQ, HP OMEN and Victus, Acer Nitro and Predator, Dell G15, G16 and Alienware, MSI Katana and Raider — come with 120, 144, 165, 240 and even 360 Hz panels. The higher the refresh rate, the smoother the picture in games, and the more precise the matching has to be:
- these panels more often use a 40-pin eDP connector, and one laptop model may come in 60 Hz and 144 Hz versions with different cables;
- in models with G-Sync and a graphics switch (MUX), the panel has to be one the manufacturer intended for the model, otherwise frame synchronization may not work;
- besides the refresh rate, we match the response time and brightness: a slow panel leaves blurry trails behind moving objects;
- after the replacement we check that the screen really runs at the stated refresh rate, without skipped frames or flicker.
Fitting a 144 Hz panel instead of a 60 Hz one is sometimes possible — if the model was also made with a fast panel and the cable fits. We check this by the code and connector before ordering, too.
Laptop OLED screens
An OLED panel has no backlight: every pixel emits light, and that brings faults of its own. After an impact, lines, colored stripes and black spots appear and spread. Over time, burn-in can occur — a ghost image left by static elements such as the taskbar. A greenish or pink tint and flicker at low brightness are also seen. If an OLED screen is completely black, the backlight has nothing to do with it: the cause is the panel itself, the cable or the panel power supply on the board.
OLED is replaced only with OLED: an LCD panel has a different thickness, connector and cable, so fitting a cheaper IPS panel is possible only in models that were made in both versions. Laptop OLED panels are most often made by Samsung Display — their codes start with ATNA. The panel is thin and must not bend, so we work with particular care during the replacement. Burn-in cannot be repaired — only a new panel helps; a dark theme and moderate brightness reduce the risk.
The display cable: when we replace it, not the panel
The display cable — an eDP or LVDS cable — runs from the motherboard through the hinge into the lid. It bends every time you open and close the laptop, and over the years the wires inside wear through. Signs of a faulty cable:
- the picture flickers, disappears or gets covered with lines at a certain lid angle;
- the picture ripples or changes its tint, and comes back when you move the lid;
- the webcam or microphone disappears together with the picture: their wires often run in the same cable as the display;
- pressing the lower part of the screen bezel makes the picture jump or go dark.
We replace the cable with one that suits the model: the same model may have different cables for 30-pin and 40-pin panels, for touch screens and for 144 Hz screens. We also check the connectors at both ends — on the board and on the panel: after a liquid spill they corrode, and careless disassembly breaks the latch. A damaged connector on the motherboard is resoldered. Sometimes the cable is worn through by a hinge that is too stiff or broken — we do not repair hinges or cases, and we will tell you so after diagnostics, so that the new cable does not share the fate of the old one.
Backlight: a dark screen while the laptop works
In an LCD panel the crystals form the image, and an LED backlight along the bottom edge provides the light. It is controlled by a driver: in modern panels the driver sits on the panel's own board, while the power and the enable signal come from the motherboard. Older laptops had a lamp (CCFL) with a separate inverter instead of LEDs. Besides a faint picture under a torch, these signs point to the backlight:
- the backlight comes on at power-up and goes off a second later;
- the backlight flickers or turns off and on by itself during work;
- the screen is noticeably dimmer than before, even at maximum brightness;
- a dark band at the bottom of the screen, uneven glow or patches of a different tint — individual LEDs are failing.
What matters next is where the cause is. If the backlight inside the panel itself has failed, we usually replace the panel: a thin laptop panel does not take disassembly well. If the backlight gets no power from the motherboard — a fuse, a switching transistor or another part of the circuit has burnt out — we do a component-level repair of the laptop board: one part is replaced, and the panel stays. This is noticeably cheaper than a new screen, which is why we never replace a panel without checking the backlight circuit.
Signs that the panel is not the problem
Before replacing the screen, one simple check helps: connect the laptop to a monitor or TV via HDMI. What it shows, and which other signs point to a different cause:
| What you see | Where the cause most likely is |
|---|---|
| The same lines, squares or “snow” on the external monitor too | The graphics chip or video memory on the motherboard: component-level repair, and BGA soldering (reballing) of the chip if needed |
| Lines and ripples appear after a while, the laptop is hot, the fan is loud | The graphics chip is overheating: the laptop needs dust cleaning and new thermal paste, then the chip is checked |
| The laptop does not turn on at all, or shows no picture after a BIOS update | The motherboard power supply or corrupted firmware, not the screen; we reflash the BIOS with a programmer |
| The screen goes dark when a phone or magnet is placed on the case near the keyboard, or goes dark by itself with the lid open | The lid sensor (Hall sensor) — a part on the board; the panel is fine |
| Lines or no picture after liquid was spilled on the laptop | Corrosion of the cable connector and circuits on the board: we clean off the corrosion and replace damaged parts |
| The picture is distorted only in one program or game, while the startup screen is clean | Most likely a driver or program issue, not the hardware; we do not work with software |
| Key marks on the screen | Dirt left on the coating by contact with the keyboard; careful screen cleaning usually removes it, the panel is fine |
Laptop brands and product lines
We replace screens on laptops of all brands — office, home, gaming and thin ultrabooks. What we take into account for the most common ones:
| Brand | Product lines | Screen specifics |
|---|---|---|
| ASUS | VivoBook, ZenBook, ExpertBook, TUF Gaming, ROG Strix and Zephyrus | VivoBook and ZenBook have OLED versions; TUF Gaming and ROG use 144–240 Hz panels, more often with a 40-pin connector |
| HP | 250 and 255, Pavilion, ProBook, EliteBook, Envy, Spectre, Victus, OMEN | Some EliteBook screens have a built-in Sure View privacy filter and are replaced only with the same kind; Envy x360 and Spectre x360 use touch assemblies |
| Lenovo | IdeaPad, ThinkPad, ThinkBook, Yoga, Legion, LOQ | ThinkPad panels are matched by the FRU number: one model may have panels of different brightness and with a PrivacyGuard filter; Yoga models are touch convertibles |
| Acer | Aspire, Extensa, TravelMate, Swift, Spin, Nitro, Predator | Aspire and Extensa more often use 30-pin HD and Full HD panels; Nitro and Predator use 144–165 Hz and higher |
| Dell | Inspiron, Vostro, Latitude, XPS, G15 and G16, Alienware | Matching by the DP/N number; on XPS the screen is often replaced as an assembly; Alienware uses panels up to 360 Hz |
| MSI | GF63, Katana, Cyborg, Sword, Raider, Modern, Prestige | One model may come in 60 Hz and 144 Hz versions, and their connectors may differ — we check the code and the connector |
| Huawei, Honor, Xiaomi, Samsung, Toshiba | MateBook, MagicBook, RedmiBook, Galaxy Book, Satellite and Dynabook | Screens with 3:2 and 16:10 aspect ratios, OLED panels and touch assemblies are common — we match strictly by the code |
What the price of a screen replacement depends on
- Panel type. TN is cheaper than IPS, and OLED costs more than both.
- Resolution and refresh rate. Full HD at 60 Hz is the most common and affordable option; 2.5K, 4K and 144–360 Hz panels cost more.
- Touch and complete assemblies. Convertibles and thin models need an assembly with glass, which costs more than a panel alone.
- The cable. If it is worn too, a new cable is added to the price.
- A cause on the board. If the panel is fine and the backlight or power circuit is at fault, the repair is usually cheaper than a new screen, let alone a new board — we replace a part, not the whole board.
We quote the exact price after diagnostics, once the panel code and the cause of the fault are known, and start work only with your consent.
What to tell us when you contact us
- The laptop model — it is on the label on the bottom of the case (Model, P/N); if the screen has been removed before, the panel code.
- What happened: a drop, an impact, pressure in a bag, a liquid spill — or the screen failed by itself.
- How the screen behaves: a crack, spots, lines, flicker, a dark screen; whether it depends on the lid angle.
- Whether there is a picture on an external monitor via HDMI.
- Screen features, if you know them: touch, OLED, 120–240 Hz.
You can send photos and a short video of the screen via WhatsApp — we will give a preliminary estimate from them, and the final one after diagnostics at Innova Service in Baku.
Get a repair quote
Choose your device and leave your number — we will contact you as soon as possible.
Prices
| Laptop screen (panel) replacement | from 100 AZN |
|---|
These are starting prices: we tell you the exact amount after diagnostics.
Frequently asked questions
How much does laptop screen replacement cost?
The price depends on the panel: repairs start from 100 AZN, and we quote the exact amount based on the laptop model and the panel code.
Can a cracked laptop screen be repaired?
No, a cracked panel is replaced. But lines and a black screen do not always mean a broken panel — sometimes the cable or the backlight is repaired.
Do you replace touch screens too?
Yes, touch screens are also replaced to match the model.
Can I keep using a laptop with a cracked screen?
You can while the picture is readable, but not for long and with care. A crack grows with heat and every time the lid is opened, the spots spread, and fragments can damage the bezel and the cable. Do not press on the screen, close the lid gently and connect an external monitor via HDMI for work. On a touch screen a crack causes false touches and the glass edges can cut your fingers — it is better not to put off the replacement.
How long does a laptop screen replacement take?
It depends on whether a panel with the right code is available and whether the cable also needs replacing or the board needs repair. We give the exact time after diagnostics, before work starts.
Will the picture look the same as before?
With a panel of the same code — yes. A compatible panel from another manufacturer may differ slightly in the white tone and brightness; this does not affect resolution or sharpness.
Will my files be kept after a screen replacement?
Yes. Replacing the panel and the cable does not touch the drive: files, programs and settings stay as they were. If the drive holds important data, we still recommend keeping a backup — it is useful for any repair.
Can you clean the laptop from dust at the same time?
Yes. Dust cleaning and new thermal paste are a separate service, but it is convenient to do them together with the screen replacement, especially if the laptop runs hot and noisy. On many models the bottom cover comes off anyway to replace the display cable.
Can I replace the panel myself?
You can, if the panel is held by screws and you know its exact code. Common mistakes: a panel with a different connector or mounting, broken bezel clips, a torn or loosely seated cable, connecting it without disconnecting the battery — this can burn out the panel or a circuit on the board. If something goes wrong, we will find the cause and fix it.
Do you replace screens on old laptops?
Yes, if we can find a panel with a matching code or a compatible one. For very old models this is not always possible, and sometimes the replacement costs more than makes sense for such a laptop — then we will tell you honestly before starting work.
Do you give a warranty on screen replacement?
Yes, we give a warranty on the work done. We check the new panel before installing it — for dead pixels and even backlighting — and after assembly we test the screen at every lid position.
Why is there no picture after a drop when the screen is not cracked?
A drop often damages not the glass but the cable or its connector: it comes loose or wears through. There may also be hidden damage to the panel without a visible crack. That is why we check the cable and the connector first and only then decide whether a new panel is needed.
Send a request — we will quote the price
- 070 262 19 19Call us
-
5a Ahmad Rajabli St. (Life Centre)Baku, AZ1052
-
Mon — Fri, 10:00–18:00Sat, Sun — closed
- service@innova.azEmail